BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


wallyduke

wallyduke
active member
active member
Yesterday I had a catastrophic failure in my drivetrain which blew a hole in the top of the Swingarm casing and caused the entire final drive and wheel to twist a good 10-15° clockwise. The strut was presumably the only thing that stopped the whole assembly from folding over completely. I was going ~85 mph, when I began to notice a quickly worsening vibration, and found my rear end engulfed in smoke when I pulled over. Pictures are certain to follow.



Last edited by wallyduke on Sun May 06, 2018 2:26 pm; edited 1 time in total

    

Barry in IN

Barry in IN
Silver member
Silver member
Sounds nasty and frightening!
But oh what a story it will make someday.


__________________________________________________
1992 K75s
    

Point-Seven-five

Point-Seven-five
Life time member
Life time member
Paralever?  U-joint failure?

Those swingarms are pretty rugged, but have their limits to what they can take.   I got rear-ended by a car last fall, broke the final drive off the Paralever swingarm.  Like you, the shock was the only thing that kept the rear wheel with the bike, not that I needed it while tumbling down the median.


__________________________________________________
Present: 1991 K100RS "Moby Brick Too"
 
Past:
1994 K75RT "Ilsa, She Wolf of the SS"
1988 K100RS SE "Special Ed"
1994 K75S "Cheetos"
1992 K100RS "Moby Brick" R.I.P.
1982 Honda FT500
1979 Honda XR185
1977 Honda XL125
1974 Honda XL125
1972 OSSA Pioneer 250
1968 Kawasaki 175
    

duck

duck
Life time member
Life time member
Glad you're OK.

Year and model?

I know of several paralever U-joints 'splodin but I've never heard of a swing arm failing.

Can't wait to see the pics.


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

wallyduke

wallyduke
active member
active member
87 K100 RS


'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2011
'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2010
'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2012

    

duck

duck
Life time member
Life time member
Holy cow! Never seen anything like that aside from Ks that have been impacted by cars and it's understandable why a swing arm might fail due to impact but to have one just fail of its own accord is a whole different story.

What's all of that black stuff on the brake reservoir? Bits of tire?


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

wallyduke

wallyduke
active member
active member
Yes, you can see where the sidewall was melting against the shock. I managed to get it in the shop and am working on disassembling it all now. I'm suspecting the driveshaft failed due to unlubed splines on the transmission side. Needless to say I am fervently searching for a suitable parts bike!

    

duck

duck
Life time member
Life time member
I think it's more likely that the U-joint blew up.  Which is pretty rare on the 2V Ks. The U-joint is sealed so there's no real preventative maintenance that can prevent that. But when it's removed for other maintenance it's a good idea to rotate it on both axes to see if any lumpiness is present.

If splines fail they just strip and spin.  And the rear drive shaft splines are where spline wear usually occurs, not the front. This of course assumes that whoever was in there last put things back together properly.  The front drive shaft splines have a clip in them and if the last person in there didn't get the front of the shaft all of the way on then I have no idea what havoc that might wreak.


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

wallyduke

wallyduke
active member
active member
I have periodically lubed the rear splines but have never opened it up any further. I've owned the bike since '09

    

MartinW

MartinW
Life time member
Life time member
I'm with Duck on this more than likely "U" joint. If the front splines had stripped noise and lack of drive would be the result.
It is not a big job to lube the front shaft splines and check the "U" joint while you are doing the rear spline lube. 
Regards Martin.


__________________________________________________
1992 K75s
    

Rick G

Rick G
admin
admin
Seen a few do that but never damage the swing arm. When a U joint lets go it is usually explosive.


__________________________________________________
"Man sacrifices his health in order to make money.
Then he sacrifices money to recuperate his health.
And then he is so anxious about the future that he does not enjoy the present; the result being that he does not live in the present or the future; he lives as if he is never going to die, and then dies having never really lived."   Dalai Lama


Bikes 1999 K1100 LT with a Big Block 1200
    

Dai

Dai
Life time member
Life time member
Different manufacturer, but I've seen a Guzzi cardan joint let go so badly that it distorted a 4mm thick steel swingarm housing and removed a large chunk from the back of the gearbox. I was riding it at the time... The gearbox and swingarm were pressed back into service with dents and bits missing for another 100,000+ miles... Twisted Evil Twisted Evil 

On another occasion I was asked to strip-service an Moto Guzzi 1000SP of unknown provenance. I took it out for a good thrash to see what might be wrong with it before the stripdown. On stripdown I discovered I'd been doing 120mph on a cardan joint with a complete set of bearings missing from one side... Shocked

So yes, having seen the destruction that an exploding cardan joint can do to a steel housing, I'm not surprised that the UJ almost managed to exit via the top of the swingarm casting.


__________________________________________________
1983 K100 naked upgraded to K100LT spec after spending time as an RS and an RT
1987 K100RT
Others...
1978 Moto Guzzi 850-T3, 1979 Moto Guzzi 850-T3 California,1993 Moto Guzzi 1100ie California
2020 Royal Enfield Bullet 500
    

Tom G

Tom G
Life time member
Life time member
Same manufacturer different model. Coming home from the Pigs and Pines run a few weeks ago on my R100R, drive totally disappeared, suspecting the clutch had failed. On removing the driveshaft (which was in 2 pieces) I suspect the front UJ had collapsed causing the Driveshaft to fail due to excessive vibrations. Luckily the UJ hung in there and did not let go. In this case I suspect the UJ. Cheers Tom


__________________________________________________
1986 K100RT Ex Police (Slightly modified)
2010 Suzuku DL650 V Strom
1992 R100R
    

wallyduke

wallyduke
active member
active member
I'm very grateful for all the tips, and now i have renewed hope I can salvage at least the gearbox from this mess. The final drive had been dripping a little oil for some time now so I'll probably try to swap that out with another unit.

    

duck

duck
Life time member
Life time member
I'd guess that you're correct that the transmission probably survived.  If the output shaft spins normally and the seal on it isn't leaking then you're probably good to go.

Please post pictures of the internal carnage when you get the swing arm off.


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

wallyduke

wallyduke
active member
active member
'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2013
'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2014
'87rs Driveshaft failure, Swingarm  rupture, strut saved my life Img_2015

    

Gaz

Gaz
Life time member
Life time member
What caused the wheel to lean over and rub on the swingarm? Did the swingarm casting break away from the final drive?


__________________________________________________
Gaz
1990 K75 6427509; 1987 R80G/S PD 6292136; 2010 G650GS ZW13381; 95 K1100LT 0232224
    

wallyduke

wallyduke
active member
active member
Negative, the casing twisted once the structural integrity was compromised. This was probably due more to the heat buildup from u-joint fragments riding between the driveshaft and casing than than from the hole itself. Speed was definitely a major factor.

    

Rick G

Rick G
admin
admin
I am not at all surprised at that swing arm twisting, it sure took a beating.
I have seen one twisted  in a crash that wasn't all that bad, bike came down sideways and twisted it about 3° but the wheel was left straight.


__________________________________________________
"Man sacrifices his health in order to make money.
Then he sacrifices money to recuperate his health.
And then he is so anxious about the future that he does not enjoy the present; the result being that he does not live in the present or the future; he lives as if he is never going to die, and then dies having never really lived."   Dalai Lama


Bikes 1999 K1100 LT with a Big Block 1200
    

wallyduke

wallyduke
active member
active member
When I turned the Swingarm over *doh* I realized the whole underside had split open as well. There is only about an inch of unbroken, but visibly stressed metal holding it together on either side. Could have been a lot worse

    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum