BMW K bikes (Bricks)

You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


1Back to top Go down   torque value for output shaft 86  k100 Empty torque value for output shaft 86 k100 on Sat May 21, 2011 11:30 am

yankeeone

avatar
Platinum member
Platinum member
Hi my clymers book has no torque value for the big bolts, on the out put shaft, on the motor I need both ends.

Brian

    

2Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Sat May 21, 2011 11:33 am

ReneZ

ReneZ
Life time member
Life time member
Sorry Mate, don't understand which ones you're talking about. Put a picture or a drawing from realoem in your post?


__________________________________________________
Greetings from Florida! Having a 'new' K  :cyclops:    Surprised-o: 

Rene


BMW K100 - 1985 (0030029) torque value for output shaft 86  k100 Rain
BMW K1200GT - 2003 (ZK01223)
    

3Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Sun May 22, 2011 11:33 am

yankeeone

avatar
Platinum member
Platinum member
All set back together and running

Brian

    

4Back to top Go down   torque value for output shaft 86  k100 Empty output shaft torque on Tue May 01, 2012 12:17 pm

jeffeaby

jeffeaby
active member
active member
i am at the same place...what are the bearing torque values?

    

5Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Tue May 01, 2012 2:58 pm

yankeeone

avatar
Platinum member
Platinum member
I was there to , with the locktite on, an no torque value for the bolts, had to run in and google it. not listed in the Clymers.

just realized that was me!!!

    

6Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Tue May 01, 2012 6:11 pm

jeffeaby

jeffeaby
active member
active member
so what's the answer!!!!~can't find it on google

    

7Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Tue May 01, 2012 6:52 pm

Inge K.

Inge K.
VIP
VIP
Being a bit more specific, would have done it easier to give an answer.


__________________________________________________
Inge K.
K100RS -86. (first owner), K1100LTSE -94.
    

8Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Tue May 01, 2012 6:59 pm

yankeeone

avatar
Platinum member
Platinum member

    

9Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Thu May 03, 2012 9:26 pm

yankeeone

avatar
Platinum member
Platinum member
Jeff, did the outputshaft workout ?

    

10Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Fri May 04, 2012 1:29 pm

jeffeaby

jeffeaby
active member
active member
thanks, your link had a value of 40 ft-lbs...seems right, was a bear to take off. assembly will be sometime next week. can't wait to get the bebuild going.

    

11Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Fri May 04, 2012 2:53 pm

yankeeone

avatar
Platinum member
Platinum member
that baby is in there pretty deep, good luck, go slow when you put it back, I set the wrench to the wrong torque, but caught it in time.

    

12Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Sat May 05, 2012 10:56 am

jeffeaby

jeffeaby
active member
active member
thanks for your replies, yankeeone. did you replace the bearings while you had the shaft out? only about 110$ so seems a good thing to do. have replaced every seal and piece of rubber so far..getting costly

    

13Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Sat May 05, 2012 1:08 pm

yankeeone

avatar
Platinum member
Platinum member
I had to change over the big bearing any way because my block was old style I did switch to a new one but the old style was only 35.00


the output shaft I bought was in really good shape
so I didn't replace the rear bearing.

    

14Back to top Go down   torque value for output shaft 86  k100 Empty Re: torque value for output shaft 86 k100 on Wed May 09, 2012 10:20 am

yankeeone

avatar
Platinum member
Platinum member
I see there is a new link for the output shaft above, it calls for 29ft pounds on those bolts, the 40 you quote is nms

    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum