1
K100 RS sidestand Mon Dec 03, 2018 7:06 pm
cfmckay
active member
Has anyone on the forum extended the sidestand on the K100 or K75?
Message [Page 1 of 1]
1
active member
2 Re: K100 RS sidestand Mon Dec 03, 2018 8:01 pm
Rick G
admin
There was a thread on here about using a hockey puck to make a thicker and broader foot for the side stand. Have a search around it will probably pop up easily.
__________________________________________________
"Man sacrifices his health in order to make money.
Then he sacrifices money to recuperate his health.
And then he is so anxious about the future that he does not enjoy the present; the result being that he does not live in the present or the future; he lives as if he is never going to die, and then dies having never really lived." Dalai Lama
Bikes 1999 K1100 LT with a Big Block 1200
3 Re: K100 RS sidestand Mon Dec 03, 2018 8:41 pm
duck
Life time member
I've done the hockey puck thing. It works but it wears out since it's rubber. I didn't bother replacing it. It needs to be shaped somewhat carefully so that the side stand goes up fully. (At least on a K1100RS with a Staintune.)
The best I've seen is the side stand that came on my turbo K75. Some prior owner welded about a 2/3" thick piece of solid steel onto the foot of the side stand.
The best I've seen is the side stand that came on my turbo K75. Some prior owner welded about a 2/3" thick piece of solid steel onto the foot of the side stand.
__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
4 Re: K100 RS sidestand Mon Dec 03, 2018 10:35 pm
MartinW
Life time member
I used a slice of rubber boat roller. I had to recess the heads into the roller and use small flat washers to make sure it didn't pull through.
Regards Martin.
Regards Martin.
__________________________________________________
1992 K75s
5 Re: K100 RS sidestand Tue Dec 04, 2018 2:10 am
duck
Life time member
I haven't tried this one yet but I found it in my stash of parts and plan to try it someday on my K100. This has a metal box welded onto the foot. I think the box is too tall and it may make the bike stand TOO upright.
The picture is a little blurry but you get the idea.
The picture is a little blurry but you get the idea.
__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
6 Re: K100 RS sidestand Tue Dec 04, 2018 3:07 am
MartinW
Life time member
Boat roller slice which can be cut to suit. The post cap is used when parking on soft ground and has multiple uses.
Can be used on the side of the road to hold small parts, water detergent dish for leak detection, dog water dish, ashtray or donation dish.
Regards Martin.
Can be used on the side of the road to hold small parts, water detergent dish for leak detection, dog water dish, ashtray or donation dish.
Regards Martin.
__________________________________________________
1992 K75s
Message [Page 1 of 1]
K100-forum.com » Technical, repair and troubleshooting » Other K bricks (K75, K1100, K1) General discussion. » K100 RS sidestand
Similar topics
Permissions in this forum:
You cannot reply to topics in this forum
|
|
|
