Another spline question

Heresy23 · 1 Another spline question Mon Jun 10, 2019 5:45 pm

Heresy23

Silver member

Number of posts : 59

Ok here’s my final drive splines..they look good .....2 things...can u use gasoline to clean before I lube? And all the gunk that’s in the housing , coups I just squirt degreaser in there? I don’t wanna ruin any seals ..and the red stuff is obviously a sealent ...should I leave it there?....I’m doing this now ....thanks

Better pics

volador · 2 Re: Another spline question Mon Jun 10, 2019 6:01 pm

volador

Platinum member

Number of posts : 268

Gasoline, kerosene (is best), denatured alcohol, brake cleaner, a good degreaser all work

It can't hurt to leave the sealant to keep out water or apply a new bead

Be on the look out for a another 16 tooth drive shaft

Heresy23 · 3 Re: Another spline question Mon Jun 10, 2019 6:30 pm

Heresy23

Silver member

Number of posts : 59

Thanks...I decided not to pull out the drive shaft and lube it ....next tire change...I don’t wanna go thru the hassle of pulling out and re-aligning....I feel like since it’s my first time I might have a issue and I was told it’s probably fine anyways

volador wrote:Gasoline, kerosene (is best), denatured alcohol, brake cleaner, a good degreaser all work

It can't hurt to leave the sealant to keep out water or apply a new bead

Be on the look out for a another 16 tooth drive shaft

duck · 4 Re: Another spline question Mon Jun 10, 2019 7:50 pm

duck

Life time member

Number of posts : 4401

volador wrote:Be on the look out for a another 16 tooth drive shaft

Why? They last much, much longer than the Z20 ones.

volador · 5 Re: Another spline question Mon Jun 10, 2019 8:27 pm

volador

Platinum member

Number of posts : 268

Good to have a spare on hand

GF Wollongong · 6 Re: Another spline question Thu Jun 13, 2019 7:54 am

GF Wollongong

Platinum member

Number of posts : 258

While we're talking splines ...

Has anyone found a use for a worn drive shaft? Got one in the garage and can't bring myself to throw it out ... can't think what to use it for?

Hoarder

MartinW · 7 Re: Another spline question Thu Jun 13, 2019 8:05 am

MartinW

Life time member

Number of posts : 2996

You can renew the splines. Cut off the old ones and weld on a new set from Motobins.
Regards Martin.

Point-Seven-five · 8 Re: Another spline question Thu Jun 13, 2019 10:19 am

Point-Seven-five

Life time member

Number of posts : 4211

I have heard of people replacing the u-joint. I have found the part number in the past and they are available for about $28. Any shop that does drive shafts should be able to do the machine work.

Sponsored content

1 Another spline question Mon Jun 10, 2019 5:45 pm

Heresy23

2 Re: Another spline question Mon Jun 10, 2019 6:01 pm

volador

3 Re: Another spline question Mon Jun 10, 2019 6:30 pm

Heresy23

4 Re: Another spline question Mon Jun 10, 2019 7:50 pm

duck

5 Re: Another spline question Mon Jun 10, 2019 8:27 pm

volador

6 Re: Another spline question Thu Jun 13, 2019 7:54 am

GF Wollongong

7 Re: Another spline question Thu Jun 13, 2019 8:05 am

MartinW

8 Re: Another spline question Thu Jun 13, 2019 10:19 am

Point-Seven-five

9 Re: Another spline question

Sponsored content