BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


1Back to top Go down   Issues with timing  Empty Issues with timing Sat Oct 21, 2023 3:40 am

svenok

svenok
active member
active member
I'm trying to get the K (1990 16v) up and running after an engine replacement. I've set the bike up on the table removed the timing cover set the pickup in spark plug 1 and used an independent battery. Warming up the bike I proceeded to remove the two mud-guards and the pick up cover and just waited 5 minutes to make sure most things are warm. 

Set the timing light to 6deg and set the cylinder to 4. loosened off the locking screws and watched the two notches.
First test, the notch was below the set one so made the adjustment and it aligned nicely.
While holding the strobe I turned the throttle and the marks moved away again, made a change and around 2500rpm they looked near in synch. 
Went to 3000-3500rmp the strobe light turns off the bike sounds like its popping and I cant see the notches as the strobe light out.

Could this be a coil issue or a spark plug issue as both have been replaced?

Drop RMP and the light turns back on and the bike sounds ok-ish


__________________________________________________
K100RS 12/90 WB1052309M0200614
    

2Back to top Go down   Issues with timing  Empty Re: Issues with timing Sat Oct 21, 2023 6:08 am

Laitch

Laitch
Life time member
Life time member
Although I'd be satisfied with the method described in the K1/K100RS 4V manual, I found this article that could have a bearing on your situation regarding your technique with the timing light.

    

3Back to top Go down   Issues with timing  Empty Re: Issues with timing Sat Oct 21, 2023 9:36 am

svenok

svenok
active member
active member
Thanks for this. I’ll check this out tomorrow


__________________________________________________
K100RS 12/90 WB1052309M0200614
    

4Back to top Go down   Issues with timing  Empty Re: Issues with timing Sat Oct 21, 2023 10:55 am

Point-Seven-five

Point-Seven-five
Life time member
Life time member
What is wrong with just lining up the notches in the HES plates?  Thousands of bricks have been running with that timing for 30+ years and hundreds of millions of miles.   Asking for a friend.


__________________________________________________
Present: 1991 K100RS "Moby Brick Too"
 
Past:
1994 K75RT "Ilsa, She Wolf of the SS"
1988 K100RS SE "Special Ed"
1994 K75S "Cheetos"
1992 K100RS "Moby Brick" R.I.P.
1982 Honda FT500
1979 Honda XR185
1977 Honda XL125
1974 Honda XL125
1972 OSSA Pioneer 250
1968 Kawasaki 175
    

5Back to top Go down   Issues with timing  Empty Re: Issues with timing Sat Oct 21, 2023 7:09 pm

Rick G

Rick G
admin
admin
+1 there you do no need to use a timing light as the marks are TDC not ignition firing point. There are many threads here about the correct wat and a strobe is not needed. Aligning the two notches will get it to within 1° every time. I have never done it any other way and never had problems.


__________________________________________________
"Man sacrifices his health in order to make money.
Then he sacrifices money to recuperate his health.
And then he is so anxious about the future that he does not enjoy the present; the result being that he does not live in the present or the future; he lives as if he is never going to die, and then dies having never really lived."   Dalai Lama


Bikes 1999 K1100 LT with a Big Block 1200
    

6Back to top Go down   Issues with timing  Empty Re: Issues with timing Sat Oct 21, 2023 8:28 pm

svenok

svenok
active member
active member
All good replies. Thanks all and I will start the search of how to.....Right now I'll try the alignment of the notches and see how it feels.


__________________________________________________
K100RS 12/90 WB1052309M0200614
    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum