BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


1Back to top Go down   New member with a question Empty New member with a question Sun May 14, 2017 11:28 pm

KurtHeide

KurtHeide
New member
New member
So, Before I ask for your advise, let the new guy introduce himself.
 I'm New Jersey born and raised, spent 4 years living in New Hampshire and Boston. Living in Florida for the past 25 years.
Been riding bikes since I was 12 and I'm 59 now! Bike history:  Honda Mini Trail Z50, ct70, Sl70, dt185, sl175, CB350, CB550K, Katana 600, VFR750F, 2 Harley Davidsons (currently a Road King) and now my first BMW: 1991 k100rs 16 valve.  I still have the VFR too
The BMW is a garage find with 7900 miles on the clock.  Replaced all the seals, tires, brakes lines, rear rotor (it was warped) and master cylinder. Rear tire spins freely while bike is on its center stand with only a negligible audible intermittent rub on the rear brakes rotor.  Calipers bled clean and are not stuck.  Brake pedal functions fine with about 2 inches of play before engaging the rear brake.  I do not ride with my foot on the brake pedal. According to the shop manual, ABS is functioning correctly as well

Here's my question: Is it normal for the rear brake rotor to be hot to the touch after normal cruising around town? If not what could I have missed that would be causing the issue?
Any thoughts on the matter would be appreciated.
Kurt

    

2Back to top Go down   New member with a question Empty Re: New member with a question Sun May 14, 2017 11:59 pm

Point-Seven-five

Point-Seven-five
Life time member
Life time member
How hot is it?  Can you hold your finger tips against it without having to pull away after a second or two?  That would indicate a temperature of 135F or less.  Does it burn them after a brief touch?  That would be a temperature above 165F.

Is the Final drive housing hot as well?  There is going to be some heat generated in the final drive that can be migrating out to the rotor. 

An interesting test would be to put the bike on the center stand, start it, and run it a while in 5th gear at about 2000 rpm.  Then see if the rotor is hot.  Running at no load should create minimal heat in the final drive, but if there is any brake drag, that will make the rotor heat up.


__________________________________________________
Present: 1991 K100RS "Moby Brick Too"
 
Past:
1994 K75RT "Ilsa, She Wolf of the SS"
1988 K100RS SE "Special Ed"
1994 K75S "Cheetos"
1992 K100RS "Moby Brick" R.I.P.
1982 Honda FT500
1979 Honda XR185
1977 Honda XL125
1974 Honda XL125
1972 OSSA Pioneer 250
1968 Kawasaki 175
    

3Back to top Go down   New member with a question Empty Re: New member with a question Mon May 15, 2017 4:02 am

charlie99

charlie99
VIP
VIP
could be interesting to find out what type of rear disk you have

there have been a few changes to the "fitted as standard " over the years

perhaps you have the solid (un vented -un slotted ) type
it appears from what I have seen so far that the slotted types go through pads quite quickly , or show significant wear in the disk  and I believe changed to the solid types after a review  perhaps about '86

the one contributing factor to brake binding that I  have noticed here in the forum , is the master cylinder fault

let me explain

whilst the piston might pump fluid quite reliably, and retract to what seems normal operation , there is an "equalizer hole " built in to the master cylinder  just a bit lower in the bore than the main reservoir feed , almost invisible to the naked eye ...and even with assistance hard to locate after all these years or use .
in most instances this equaliser hole becomes blocked with crud , worn rubber, poor fluid maintenance , and just plain lack ofa regular flush .. sound familiar? 

with the bypass - equalizer working properly , it lets the callipers relax away from the disk ...without this action, binding is quit common , in fact ..bleeding the rear system can become problematic in many instances .

our old mate rossko  delved into this issue and finally found the offending "port "  after much searching

there is a thread in here that follows the original post (perhaps you could use the "search feature " to locate the orginalposts

but heres the "found " picture .

we had surmised that a pin pricker- portagas valve cleaner  type of tool would aid in the cleaning of the equalizer hole . as there is a bung for the reservoir feed into the master cylinder , that doesn't let you access that equalizer hole ....like the front master cylinder reservoir does 

New member with a question Brake_10

it may not solve your particular ..issue... but I believe that if you get the working parts of the system working properly you just may minimise the
effects on the rear disk brake wear-heating issues

good luck


__________________________________________________
cheezy grin whilst riding, kinda bloke ....oh the joy !!!! ...... ( brick aviator )

'86 K100 RT..#0090401 ..."Gerty" ( Gertrude Von Clickandshift ) --------O%O
'86 k100 rs.. #######..  "Fred " (f(rame) red ) ( Fredrick leichtundschnell ) - -
bits and pieces from many kind friends across the k100 world ...with many thanks ..
1987 k100rs ########   "Red"  - (red sports rs TWB style )
1989 K100rt #009637   "Black Betty"  (naked rt ala Nigel , now sporting an rs main fairing )
    

4Back to top Go down   New member with a question Empty Re: New member with a question Mon May 15, 2017 7:18 am

Dai

Dai
Life time member
Life time member
The other thing worth checking for is crap in the caliper preventing the pads from moving freely. I did strip one rear caliper where there was so much build up of dirt and rust (from the pad backing) that the pads were permanently in contact with the disc.


__________________________________________________
1983 K100 naked upgraded to K100LT spec after spending time as an RS and an RT
1987 K100RT
Others...
1978 Moto Guzzi 850-T3, 1979 Moto Guzzi 850-T3 California,1993 Moto Guzzi 1100ie California
2020 Royal Enfield Bullet 500
    

5Back to top Go down   New member with a question Empty Re: New member with a question Mon May 15, 2017 2:18 pm

duck

duck
Life time member
Life time member
Another thing you might try is taking off the brake line and cleaning it out to make sure there is no crap/crud in it.


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum