BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


1Back to top Go down   light switch - The light control (Right side) Empty The light control (Right side) Tue Apr 03, 2012 4:39 am

komandoalicante

komandoalicante
Silver member
Silver member
Here's the light control (Right side) on the back we will remove the piece that holds the wires, removing the screw marked with arrow

light switch - The light control (Right side) 001

Removing this screw allows us to pull the turn signal switch to remove

light switch - The light control (Right side) 002

Now let's remove the screw holding the button turn signal cancellation. You have to pay special attention, because in this hole there's the light switch screw marked with the black arrow, note that the cancellation is in a vertical plane while the light is in a horizontal plane.

light switch - The light control (Right side) 003

This is the position of the screwdriver to remove the screw-flash cancel button

light switch - The light control (Right side) 004

When you start to loosen the screw, you must be careful to hold the button, so do not jump the ground and slip

light switch - The light control (Right side) 005

In the button you can see the pier and slip switch

light switch - The light control (Right side) 006

light switch - The light control (Right side) 007

And what is your position.

light switch - The light control (Right side) 008

Now you can see the screw on the remote control of lights, as I said this is in a horizontal plane.

light switch - The light control (Right side) 009

light switch - The light control (Right side) 010

Never remove the screw holding the plastic before.

light switch - The light control (Right side) 011

light switch - The light control (Right side) 012

Carefully remove the slide it is below the pier and the steel ball.

light switch - The light control (Right side) 014

The steel ball is often left in the hole, look carefully.

light switch - The light control (Right side) 015

When you remove these screws has been very careful with contact steel ball and spring brass

light switch - The light control (Right side) 016

light switch - The light control (Right side) 017

Now carefully lift the white slide

light switch - The light control (Right side) 018

You can see the spring contact and the ball

light switch - The light control (Right side) 019

light switch - The light control (Right side) 020

Your turn to clean

light switch - The light control (Right side) 021

Dismantle the emergency stop

light switch - The light control (Right side) 022

With a small screwdriver you a little leverage

light switch - The light control (Right side) 023

Remember holding work when removing red cables, since the part which is also very sensitive

light switch - The light control (Right side) 024

light switch - The light control (Right side) 025

Do not miss these two springs

light switch - The light control (Right side) 026

light switch - The light control (Right side) 027

As the cable sheath is too damaged, you can put some heat shrink, we need to remove the connector

light switch - The light control (Right side) 031

With a small screwdriver do a bit of pressure to bend a small tabs that keep out the contact back. Look at the following two photos

light switch - The light control (Right side) 032

By pressing the tabs have collapsed, allowing passage through the plastic connector

light switch - The light control (Right side) 033

Now we have to open the tabs, so that when we insert the contacts into the connector, are set

light switch - The light control (Right side) 034

With a little patience is out the connector.

light switch - The light control (Right side) 038

This is the reason for removing the connector

light switch - The light control (Right side) 039

light switch - The light control (Right side) 042

Apply heat

light switch - The light control (Right side) 043

light switch - The light control (Right side) 044

Cleaning and lubrication

light switch - The light control (Right side) 045

That's how the contacts were dirty

light switch - The light control (Right side) 046

I had a problem with the intermittent contact

light switch - The light control (Right side) 047

We pulled the pin
light switch - The light control (Right side) 048

The dirt was widespread, clean and assemble

light switch - The light control (Right side) 050

More cleaning

light switch - The light control (Right side) 052

We cleaned

light switch - The light control (Right side) 053

Clean and lubricated (Vaseline)

light switch - The light control (Right side) 055

Clean and grease

light switch - The light control (Right side) 056

light switch - The light control (Right side) 058

light switch - The light control (Right side) 059

This part is very delicate, the contact is easily damaged, and if you lose your way will cost you to make it work well so arming you patience.

light switch - The light control (Right side) 060

All clean and ready for lubricating oil on

light switch - The light control (Right side) 061

Already lubricated and cleaned contact

light switch - The light control (Right side) 062

You must be very careful when mounting the slide with the contact and spring, spring ball and the ball, holding the whole loosely and put the screw.

light switch - The light control (Right side) 063

The ball is under the dock

light switch - The light control (Right side) 064

We present the slide while holding the whole

light switch - The light control (Right side) 065

And finally look with screw

light switch - The light control (Right side) 066

EThis is the smallest screw, if you put another in his place, you can remove the front and not look good.

light switch - The light control (Right side) 067

We will mount the flash cancel button, you can now take advantage of and clean up a little, well, you can carefully review the outline of the symbol, with a permanent marker.

light switch - The light control (Right side) 068

Clean and lubricated

light switch - The light control (Right side) 069

Hold it while you put the screw

light switch - The light control (Right side) 070

Remember that in this there is the sliding screw the lights but on another level.

light switch - The light control (Right side) 071

And finally put in place the right turn signal button and screwed.

light switch - The light control (Right side) 072

light switch - The light control (Right side) 073

this. this, this is all folks.

Regards


__________________________________________________
SAK3 and komandoalicante is the same person

In March we made a International meeting  KEDADA ALICANTE of BMW motorcycle K in  Spain.

The last meeeting  March 2020

https://youtu.be/hfqxlGeEVsY
https://picasaweb.google.com/100417997445250027277
    

2Back to top Go down   light switch - The light control (Right side) Empty Re: The light control (Right side) Tue Apr 03, 2012 6:18 am

mike d

avatar
Life time member
Life time member
Excellent, informative post - Thanks.

Mike

    

3Back to top Go down   light switch - The light control (Right side) Empty Re: The light control (Right side) Tue Apr 03, 2012 10:02 am

beanoldboy

beanoldboy
Life time member
Life time member
Thank you , this is a valuable and informative piece. It will find its way into the collection of knowledge i am certain, very good photography also, please keep it coming.

http://www.airware.com.au
    

4Back to top Go down   light switch - The light control (Right side) Empty Re: The light control (Right side) Tue Apr 03, 2012 10:57 am

greecek100rt

greecek100rt
active member
active member
nice job

use a dremel with a small brush (brass) to renew the plastic buttons



light switch - The light control (Right side) Dsc03710

    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum